Your Shopping Basket () €0.00 ex-VAT (€0.00 inc-VAT)

SkyRC D100-V2 Dual Charger 2x100W 240VAC/12VDC

€129.00

Product Code: SK100131
Condition: New

Manufacturer: Imax

Product Information

Earn Reward Points: 106

Earn Discount: €1.06


SkyRC D100-V2 Dual Charger 2x100W 240VAC / 12VDC

SKYRC D100-V2 - AC / DC Dual Balance Charger / Discharger / Power Supply:
SKYRC D100v2 is a twin-channel charger with two independent circuits
that can charge batteries or varying chemistries (LiPo / LiFe / Lilon / LiHV
/ NiMH / NiCd / Pb) simultaneously. Capable of operating as a power supply
with the maximum output of 100W helps the hobbyists to power other
DC equipments. With its unprecedented function or voice guide,
even a freshman can operate this charger easily.
Additional feature including our "SCAN TO GO" and smart phone control via Bluetooth.


Twin-channel Charger:
SKYRC D100v2 allows you to plug 2 batteries into one charger at the same time,
and it will be intelligent and automatic. To top of it, the batteries are not even
needed to have the same configuration. You can connect
different chemistry (LiPo / LiFe / LiLe / LiHV / NiMH / NiCd / Pb) batteries
into any of the charging ports.


Dual Input and Power Distribution:
The input of the charger is AC 100-240V and DC 11-18V. In DC mode,
the power of each channel is 100W. Total power is 200W. In AC mode,
it supports power distribution, between Channel A, Channel B & Power Supply.
For example, if both channel A and channel B are set to 40W, then, the DC power
is 20W.The total power is 100W. (40W + 40W + 20W = 100W)

 
Optimized Operating Software:
SKYRC D100v2 features the so-called AUTO function that sets the feeding
current during the process of charging or discharging. Especially for lithium
batteries, it can prevent the overcharging which may lead to explosion due to
the user's fault. It can disconnect the circuit automatically and alarm once detecting
any malfunction. All the programs of this product were controlled through two way
linkage and communication, to achieve the maximum safety and minimize the
trouble. All the settings can be configured by users!


DC Power Output Supported:
With the unique feature of DC power source.


Voice Guide:
Purposes to make the charger more intuitive and user friendly.


Special Features:
Battery Memory (Data Store / Load)
The charger can store up to 10 different charge / discharge profiles for each channel.
You can keep the data pertaining to the setting of the battery or continuous charging
or discharging. Users can call out these data at any time without any special
program setting.

Terminal Voltage Control (TVC):
The charger allows user to change the end voltage. (for expert user only)


SkyCharger APP:
Smart Phone Control via Bluetooth (both iOS and Android):
The Bluetooth 4.0 connectivity allows the user to control and monitor the D100 v2
comfortably through a portable device such as smartphone, iPad, or iPhone.
The iOS app can be downloaded from the iTunes Store, the Android app from
Google Play Store. Operation of the app is self-explanatory and the same on iOS
and on Android. Explicit pairing is not required; after download and installation
just activate Bluetooth on your mobile device and launch the app.
D100 v2 and your device will establish Bluetooth connection automatically.


SCAN TO GO:
A very unique feature of D100v2 is SCAN TO GO (automatic charging system).
As the range of battery types and capacity is becoming more and more, each battery
requires its own dedicated charging process. It is easy to set up the charger
incorrectly for a specific type of battery.


THE REVOLUTIONARY SCAN TO GO:
A revolutionary information. The user can create a unique QR Code by using "SkyCharger"
apps. Print it and fit it on the battery.


Using your smart phone and launch "SkyCharger" app. Since all the essential
information is stored in the QR Code. All you need to do is press the Scan button,
and the charge or discharge process will start automatically.


Charge Master - PC Control Software:
The free "Charge Master" software gives you unparalleled ability to operate
the charger through the computer. You can monitor voltage, cell voltage and
other data during charging, view charge data in real-time graphs. And you can initiate,
control the charger from "Charge Master". The user can monitor voltage, cell voltage
and other data during charging, view charge data in real-time graphs,
and can also control and update firmware from "Charge Master".


Balancing Individual Cells Battery During Discharging:
During the process of discharging, SKYRC D100v2 can monitor and
balance each cell of the battery individually. Error message will be done and the process
will be automatically if the voltage of any single cell is abnormal.


Fast Charge and Storage Mode or Lithium Battery:
Function of the two modes differs from each other. "FAST CHG" minimizes battery
charge time, while "STORAGE" has the capacity to control the final battery voltage,
which is necessary and helpful for a rarely used battery.


Re-Peak Mode or NiMH / NiCd Battery:
In re-peak charge mode, the charger can be peaked once again,
twice or twice in a row automatically. This is good for making the battery fully charged.


Delta-peak Sensitivity for NiMH / NiCd:
Delta-peak sensitivity for NiMH / NiCd battery: The automatic charge termination
program based on the principle of Delta-peak voltage detection. When the battery's
voltage exceeds the threshold, the process will be terminated automatically.


Cyclic Charging / Discharging:
1 to 5 cyclic and continuous process of charge> discharge or discharge> charge is refreshing
and balancing to stimulate the battery's activity.

Automatic Charging Current Limit:
You can set up your NiMH or NiCd battery, it is useful for the NiMH battery and low-impedance
and capacity in the 'AUTO' charging mode.


Battery Voltage Meter:
The user can check the total voltage, the highest voltage, the lowest voltage and each cell's voltage.


Battery Internal Resistance Meter:
The user can check the total internal resistance and each cell's internal resistance.


Capacity Limit:
The charging capacity is always calculated as the charging current multiplied by time.
If the charging capacity is exceeded, the process will be terminated automatically when
you set the maximum value.


Temperature Threshold:
The battery's internal chemical reaction will cause the temperature of the battery to rise.
If the temperature limit is reached, the process will be terminated. This is only available in the package.


Processing Time Limit:
You can limit the maximum process time to avoid any possible defect.


USB Power 5V / 2.1A:
You can charge your phone and tablet using the built-in USB power output port.

Specs:
    DC Input Voltage: 11-18V
    AC Input Voltage: 100-240V
    Display Type: 128x64 LCD
    Display Backlight: Cool White
    Case Material: Plastic
    Controls: Five Buttons
    Case Size: 153 x 140 x 67 mm
    Weight: 668 g
    DC Power Supply Output: 13.8V / Max. 100W
    PC Communications: USB Port for PC Control & Firmware Upgrade
    External Port: 2-6S Balance Socket-XH, Temperature Probe Socket, Battery Socket,
AC / DC Input, DC Output, Micro USB Port for PC, 5V-2.1A USB Output.
    Delta Peak Detection for NiMH / NiCd: 3-15mV / cell / Default: 4mV / cell
    Charge Cut-off Temperature: 20ºC-80ºC (adjustable)
    Charge Voltage: NiMH / NiCd: Delta peak detection
    LiPo: 4.18-4.25V / cell
    LiIon: 4.08-4.2V / cell
    LiFe: 3.58-3.7V / cell
    LiHV: 4.25-4.35V / cell
    Balance Current: 300mA / cell
    Reading Voltage Range: 0.1-26.1V
    Battery Types / Cells: LiPo / LiIon / LiFe / LiHV: 1-6cells
    NiMH / NiCd: 1-15 cells
    Pb: 2-20V
    Battery Capacity Range: NiMH / NiCd: 100-50000 mAh
    LiPo / LiIon / LiFe / LiHV: 100-50000 mAh
    Pb: 100-50000 mAh
    Charge Current: 2x 0.1A-10.0A
    Safety Timer: 1-720 minutes / OFF
    Charge Wattage: AC 100W (Support Power Distribution) DC 2x100W
    Discharge Current: 2x 0.1A-2.0A
    Discharge Cut-off Voltage: NiMH / NiCd: 0.1-1.1V / cell
    LiPo: 3.0-3.3V / cell
    LiIon: 2.9-3.2V / cell
    LiFe: 2.6-2.9V / cell
    LiHV: 3.1-3.4V / cell
    Pb: 1.8-2.0V / cell
    Discharge Wattage: 2x 10W
    Balance Cells: 2-6 cells
    Memory: 10x2 Different Charge / Discharge Profiles
    Charge Method: CC / CV for Lithium Types and Lead (Pb) Batteries & Delta-peak Sensitivity for NiMH / NiCd.


Included:
    SKYRC D100v2 Charger
    2x XH Adapter
    2x Charging Cable
    2x Banana connectors with XT60 connector Charging Cable
    Power Cord

 

 

 

Customer Reviews

This product hasn't been reviewed yet. Write a review

 


 CopyRight Righthere Innovations (2007 - 2020)
 

 

Mobile Site